Splitter plate (aeronautics)

A splitter plate is a component in some jet aircraft, used to control the airflow into the engine. Where the engine air intake is mounted partway back along the fuselage or under the wing, the splitter plate diverts the boundary layer away from the engine intake. It is a form of boundary layer control.

Diverting the boundary layer

When a body, such as a wing or a fuselage, passes through a fluid such as the air, a boundary layer of fluid attaches to the body and moves along with it. If this layer enters the air intake of a jet engine, it can affect performance.

In order to stop this boundary layer problem from happening, a splitter plate may be used to separate the boundary layer from the fast-moving free airflow and divert it away from the engine intake.

Many splitter plates have a series of holes drilled into the surface closer to the engine side of the intake.^[1] Suction is applied to these holes, further reducing the boundary layer.^{[citation needed]}

Airplanes

References

^ Rogoway, Tyler (2018-05-18). "The YF-23's Air Inlet Design Was Its Most Exotic Feature You Never Heard Of". The Drive. Recurrent Ventures. Archived from the original on 2018-05-21. Retrieved 2023-04-07. Having holes drilled into splitter-plates wasn't new. It had been done many times in the past to remove the boundary air that began to manifest itself on the plate itself before entering the engine. For instance, the Eurofighter EF2000 has this feature on its upper splitter plate that is easy to spot. The Super Hornet also uses it on the inside of its intakes. Older aircraft, like the F-4, also used perforations on their splitter plates to remove air clinging to the intake's surface.

Hughes, Donald L; Holztman, Jon K; Johnson, Harold J (1972). "Flight-Determined Characteristics of an Air Intake System of an F-111A Airplane" (PDF). Technical Note. D–6679. NASA. Retrieved 15 February 2013.
Hünecke, Klaus (1997). Jet Engines. England: Airlife. pp. 76–79. ISBN 1853108340. ... the thickening of the boundary layer that develops at high angles-of-attack along the lower side of the fuselage forebody [in the F-16]. In order to prevent low-energy flow from entering the engine, the intake had to be offset from the fuselage to free it from the boundary layer, which uninterruptedly passes along the fuselage. The intake cowl [of the F-16] features a moderately blunt lower lip that transitions into a sharp leading-edge extension or splitter plate on the upper side (close to the fuselage).

External links

This article about aircraft components is a stub. You can help Wikipedia by expanding it.

[Rogoway-1] Rogoway, Tyler (2018-05-18). "The YF-23's Air Inlet Design Was Its Most Exotic Feature You Never Heard Of". The Drive. Recurrent Ventures. Archived from the original on 2018-05-21. Retrieved 2023-04-07. Having holes drilled into splitter-plates wasn't new. It had been done many times in the past to remove the boundary air that began to manifest itself on the plate itself before entering the engine. For instance, the Eurofighter EF2000 has this feature on its upper splitter plate that is easy to spot. The Super Hornet also uses it on the inside of its intakes. Older aircraft, like the F-4, also used perforations on their splitter plates to remove air clinging to the intake's surface.

[1]

v t e Aircraft components and systems
Airframe structure	Aft pressure bulkhead Cabane strut Canopy Crack arrestor Cruciform tail Dope Empennage Fabric covering Fairing Flying wires Former Fuselage Hardpoint Interplane strut Jury strut Leading edge Lift strut Longeron Nacelle Rib Spar Stabilizer Stressed skin Strut T-tail Tailplane Trailing edge Triple tail Twin tail V-tail Vertical stabilizer Wing root Wing tip Wingbox
Flight controls	Aileron Airbrake Artificial feel Autopilot Canard Centre stick Deceleron Dive brake Dual control Electro-hydraulic actuator Elevator Elevon Flaperon Flight control modes Fly-by-wire Gust lock HOTAS Rudder Rudder pedals Servo tab Side-stick Spoiler Spoileron Stabilator Stick pusher Stick shaker Trim tab Wing warping Yaw damper Yoke
Aerodynamic and high-lift devices	Active Aeroelastic Wing Adaptive compliant wing Anti-shock body Blown flap Channel wing Dog-tooth Drag-reducing aerospike Flap Gouge flap Gurney flap Krueger flap Leading-edge cuff Leading-edge droop flap LEX Slats Slot Stall strips Strake Variable-sweep wing Vortex generator Vortilon Wing fence Winglet
Avionic and flight instrument systems	ACAS Air data boom Air data computer Aircraft periscope Airspeed indicator Altimeter Annunciator panel Astrodome Attitude indicator Compass Course deviation indicator EFIS EICAS Flight management system Glass cockpit GPS Head-up display Heading indicator Horizontal situation indicator INS ISIS Multi-function display Pitot–static system Radar altimeter TCAS Transponder Turn and slip indicator Variometer Yaw string
Propulsion controls, devices and fuel systems	Autothrottle Drop tank FADEC Fuel tank Gascolator Inlet cone Intake ramp NACA cowling NACA duct Self-sealing fuel tank Splitter plate Throttle Thrust lever Thrust reversal Townend ring War emergency power Wet wing
Landing and arresting gear	Aircraft tire Arrestor hook Autobrake Conventional landing gear Drogue parachute Landing gear Landing gear extender Oleo strut Tricycle landing gear Tundra tire
Escape systems	Ejection seat Escape crew capsule
Other systems	Aircraft lavatory Auxiliary power unit Bleed air system Deicing boot Emergency oxygen system Environmental control system Flight recorder Hydraulic system Ice protection system In-flight entertainment system Landing lights Navigation light Passenger service unit Ram air turbine

Diverting the boundary layer

Airplanes

See also

References

External links